Get Quote >

Get A Price Estimate Via E-Mail for a Replacement Remanufactured Transmission

Get A Free Remanufactured Transmission Estimate By Email

Fair Remanufactured Transmission Cost
By Transmission Model

Don't know your transmission model yet? Scroll down to find your transmission model by vehicle

Need bigger text? Download the full cost guide PDF to zoom in

Keeping Your Transmission Cool

► Auxiliary Transmission Oil Coolers

 Transmission Heat Temperature Failure Chart

► How to Install an Auxiliary Transmission Oil Cooler

► Cost for Transmission Oil Cooler

Save Your Transmission by Reducing Heat

INFORMATION YOU NEED TO KNOW

The factory transmission cooling system uses the engine’s radiator to cool the transmission fluid.  Thus, when your engine runs hot your transmission also runs hot. The transmission can also overheat in stop and go traffic, when traveling on mountain roads, when towing another vehicle or trailer and on long trips.

Numerous other conditions, including low fluid level can also cause your transmission to overheat. More often than not, when a transmission overheats, it can go undetected until the trouble symptoms begin to show up.  By then, the damage is done - a replacement is normally needed.

The chart below provides a graphic illustration of just how devastating excessive heat is to the life expectancy of an automatic transmission.  The general rule of thumb is that for each 20 to 25 degree increase in temperature the transmission's life expectancy is cut in half.  Keeping your transmission cool is the key to longevity.

Transmission and Transaxle
Heat Temperature Failure Chart

Overheating is a Transmission Killer

According to The Automatic Transmission Rebuilders Association (ATRA), an International trade association for the professional automatic transmission repair industry, approximately 90% of all automatic transmission failures are due to fluid (ATF) breakdown caused by excessive heat.  As ATF heats up it becomes oxidized and loses its ability to lubricate and cool the transmission.  Poor lubrication causes friction, which produces more heat.  This is why it is extremely important to routinely check both the ATF level and condition in your vehicle.

Spending 5 to 10 minutes once a month checking your vehicle's transmission fluid level and condition could save you thousands of dollars in repair bills.

The problem of transmission overheating can be resolved by installing an auxiliary transmission oil cooler.  As a DIY project, you'll pay between $30 and $60 for the oil cooler and spend 1 1/2 to 2 hours on installation.

You can have a local transmission shop install a transmission oil cooler in your vehicle.  Expect to pay between $150 and $250 for the job.  Either way, installing an auxiliary transmission oil cooler is one of the best investments you can make in protecting your transmission from overheating and certain failure.

175 Degrees:  100,000+ miles  (Normal is typically 179 to 195 degrees)
200 Degrees:    90,000 miles
225 Degrees:    55,000 miles  (Pressure Drops)
250 Degrees:    25,000 miles  (Valves Stick)
275 Degrees:    17,000 miles  (Varnish Forms)
300 Degrees:      4,000 miles  (Seals & Clutches Burn)
325 Degrees:    TRANSMISSION FAILURE

Keep your transmission from overheating and you eliminate the #1 cause of premature transmission failure.

As repeated throughout this Website, excessive heat is a transmission killer.  Keep your transmission from overheating and your chances for transmission failure are drastically reduced.

The best way to insure your transmission does not overheat is to install an auxiliary (secondary) transmission oil cooler.  The cost is minimal and the installation is easy. A person with minimal automotive skills can install a transmission oil cooler in a couple of hours or less.

Transmission Oil Cooler Installation (Step-by-Step Guide)

Note: Installation instructions may be included in the transmission oil cooler kit you purchase. If so, follow those instructions first and use this information only if needed.

TOOLS NEEDED

Screwdriver for hose clamps
Pliers
Hand Drill and a selection of drill bits
Razor knife to cut rubber cooler hose
Hacksaw or small pipe cutter to cut cooler lines
A drain pan or small container to catch fluid

Before you begin:

1. Cut hoses so they are a couple of inches longer than your rough measurements.

2. The cooler must mount no closer than 1/2” in front of the radiator or A/C condenser.  The secondary transmission cooler must be securely mounted so that it does not come in contact with any moving parts.

1. Connect the cooler using the illustration below as a guide.  On all automatic transmissions, the transmission oil flows from the transmission through the original equipment cooler, (which is located inside the radiator), and then back to the transmission.

When a auxiliary transmission oil cooler is installed, the heated transmission oil flows from the transmission to the original equipment oil cooler inside the radiator - then to the auxiliary oil cooler and then back to the transmission.  See illustration below.

Connecting the Cooler

2. Place a catch pan under the radiator.  Using an open-end wrench, disconnect one of the oil cooler lines where it enters the radiator.  Now, ensure that the vehicle cannot start during cranking.  Have a helper crank the engine for just a few seconds.  The transmission oil will flow either from the radiator (where you removed the cooler line) or from the disconnected cooler line.  If the oil flows from the radiator, this is the outlet.  If the oil flows from the disconnected cooler line, it means the oil flows out of the radiator at the other cooler line, making it the outlet.

Now that you know which is the outlet, install the hose connector adapter that came with the auxiliary oil cooler kit to the outlet neck on the radiator.

3. Attach the rubber hose to either of the outlets on your new auxiliary cooler.  Slip a hose clamp over the connection point.  Run the other end of the hose to the adapter you placed on the radiator in the previous step.  Mark the needed hose length and cut hose accordingly.  Slip the hose over the adapter fitting and secure with a hose clamp.  Tighten hose clamps to 15 to 20-inch pounds of torque.

4. 
Repeat these same hose fitting instructions for the second hose – being certain to torque the clamps at 15 to 20-inch pounds.

1. The transmission cooler kit you purchased will include the mountingtransmission oil cooler hardware needed to mount the cooler.  The cooler should be mounted ½ to 1 inch in front of the radiator or A/C condenser for vehicles with air conditioning.

2. Find the oil cooler lines.  These are metal tubes that connect to the transmission on one end and the radiator at the other end.

3.
Position the auxiliary transmission oil cooler so its inlet and outlet tubes face the existing transmission oil cooler lines.

4. With the mounting hardware provided with your oil cooler kit, mount the cooler 1/2 to 1 inch in front of the radiator or A/C condenser.

Note: The cooler may be mounted in a different location, but doing so may reduce the cooler’s effectiveness.

Mounting the Cooler

1. Check the auxiliary cooler to be sure it is mounted securely and that there is some space between the cooler and the radiator or A/C condenser.

2. Check the hose clamps for proper tightness

3. Check to be sure the rubber hoses are not touching any other parts and that there are no sharp bends or kinks.

4. Start the engine and allow it to warm up to normal operating temperature.  Check for leaks as the engine is warming.

5. Check transmission fluid level and add fluid if necessary.  The installation of the auxiliary cooler should require some additional fluid to be added.

IMPORTANT NOTE: During the first week after installing a transmission oil cooler and then periodically from then on, check connections for leaks and check hose clamps to be certain they remain tight.  Also, don't forget to check the transmission fluid level and condition periodically.

Congratulations, with a auxiliary transmission oil cooler installed, you can drive your vehicle with more confidence and peace of mind knowing that a cooler running transmission is a longer lasting transmission.

Check the Installation

Automatic Transmission Repair Cost
What is a fair price to pay for various transmission repairs? What kinds of repairs does a transmission need?

Transmission Rebuild Cost
Does your transmission need rebuilt? Fair price guide for the price range of a transmission rebuild.

Remanufactured Transmission Options and Cost
Considering a remanufactured transmission? Here are costs and options for how to purchase.

Get a Free Transmission Estimate by Email
Want an estimate for a remanufactured transmission? Fill out the form here to get an estimate via e-mail.

How to Replace a Transmission Torque Converter Clutch Solenoid
What is a transmission torque converter clutch solenoid and how to replace one if it goes bad.

How to Replace a Transmission Pressure Control Solenoid
What is a transmission pressure control solenoid and how to replace one if it goes bad.

How to Replace Transmission Solenoids
Guide to various automatic transmission solenoids, how they work, and DIY instructions.

How to Know Which Transmission Fluid to Use?
What fluid type do you need for your specific transmission? Use this guide to find out.

How to Remove and Install an Automatic Transmission - (RWD)
If you facing a transmission replacement, you can reduce the cost considerably by removing and re-installing the transmission yourself.  Here we provide step-by-step instructions for remove and replacing a transmission. 

How to Replace a Transmission Speed Sensor
For most vehicles, the speed sensor is plugged into the transmission (or transaxle).  When the speed sensor fails the speedometer stops working and shifts may become erratic.  Replacing a speed sensor is easy.

How to Locate and Fix an Automatic Transmission Fluid Leak
Vehicle owners become aware of a transmission fluid leak either when checking the fluid level and seeing that it is low or seeing a red colored fluid on their driveway or garage floor.

How to Release a Shifter Lever That is Stuck in Park
Nothing is more frustrating that getting into your car and the gear shifter lever being locked in Park.  Here we explain how to release the shifter, the causes, how to repair and the estimated cost.

How to Install an Automatic Transmission Oil Cooler
Installing an auxiliary transmission oil cooler can protect your transmission from overheating and failure. Excessive heat can ruin a perfectly good transmission very quickly. Coolers are inexpensive and easy to install.  

How to Change the Fluid and Filter in an Automatic Transmission
Keeping clean fresh fluid in your transmission is the number one thing you can do to protect the transmission from premature failure.  These DIY transmission fluid and filter change procedures are easy to follow.

How to Check the Condition of your Automatic Transmission Fluid
Learn how to check the condition of transmission fluid, what the different conditions mean and what, if anything, you need to do to keep your transmission running smooth.

How to Check Your Automatic Transmission Fluid Level
Learn the correct procedure for checking transmission fluid level.  Many people do it wrong, so here is the easy way.

How to Replace a Transmission Neutral Safety Switch
The neutral safety switch is a safety feature that prevents the engine from starting when the transmission or transaxle is in gear.  When the switch fails, the engine may not crank or it may start in gear.

How to Flush Your Automatic Transmission
A transmission fluid flush can be performed without a transmission flush machine - and it's safer for high mileage vehicles.

What Transmission Do I Have?
A guide to determining which transmission model you have based on the year, make, model and engine size.

What is Limp Mode?
When a transmission fault is detected by the OBD-II system, the transmission may go into fail-safe (or "limp" mode as it is also called) in order to protect the transmission from internal damage

Common Transmission Problems and Solutions
Most vehicle problems, including automatic transmission problems, reveal themselves in one way or another. Learning to recognize these warning signs can save you a great deal of money and vehicle down time.

Transmission Diagnostic Trouble Codes
Diagnostic Trouble Codes P0700 through P0799 are transmission related OBD-II codes.  Any code within this range point to a transmission related fault..

How to Inspect and Repair CV Axles and CV Joints
CV (constant-velocity) axles, (also known as half-shafts), are used in front-wheel drive vehicles to transfer the engine’s power from the transaxle to the two drive wheels. 

Auto Repair Safety
When working on or around any vehicle injuries can and do occur.  Please read these Safety Precautions before starting your next automotive service/repair project.

A Library of "Do-it-Yourself" Service and Repair Guides 
Fix the following errors:
Hide